48
Articles avaible
In the databases
666
Registered Users
On the website
00:00
Loading...
Europe/Brussels

Flashing a Huawei Ascend Y511 Smartphone with a Windows System

Lorem ipsum dolor sit amet, consectetur adipisicing elit, sed do eiusmod tempor incididunt ut labore et dolore magna alliqua. Ut enim ad minim veniam, quis nostrud exercitation ullamco laboris nisi ut aliquip ex ea commodo consequat. Duis aute irure dolor in reprehenderit in voluptate velit esse cillum dolore eu fugiat nulla pariatur. Excepteur sint occaecat cupidatat non proident, sunt in culpa qui officia deserunt mollit anim id est laborum.

What's needed:

USB data cable

MediaTek USB VCOM drivers

SP Flash Tool ( Latest version )download link

First of all, make sure that you have MediaTek DA USB VCOM drivers installed.

Flashing the whole ROM

First of all open SP Flash Tool, then click Scatter-loading button to load the correct scatter file 

(MT6575_Android_scatter_emmc.txt or MT6577_Android_scatter_emmc.txt, depending on which phone you have) for your device and ignore any message that may appear.

Turn off your phone, remove the battery and replace it after some seconds (and don't turn on the phone).

Press F9 (or hit Download button) and connect your phone into the computer via USB data cable.

The process will start and a red progress bar will appear.

After the red progress bar is complete, there will appear a purple progress bar.

Right after the purple progress bar is complete, a message will appear underneath it:

“Please insert USB cable in x seconds” and then the download will start right away (you will see the yellow progress bar filling up)

When the yellow bar is complete, you'll get a popup with a green circle and Download OK message,

which means that the process has been successfully terminated.

You can now safely disconnect your phone and turn it on. The process ends here.

Flashing only part of the ROM
In case you want to flash just one part of the ROM, that is also possible. In the shown example, only recovery image will be flashed.
Deselect all parts except the one(s) you want to flash and then press F9 (or hit Download button).
The tool will immediately show a warning because not all parts are selected, but you should continue anyway. Safely press Yes to continue.
The download of the chosen partition image will start and after the yellow bar is complete, the popup with the green circle should appear.
Please note that, even though it isn't mandatory to select it on the list of images to flash, 
preloader file must be present in the same folder as the other partition(s) that you want to flash, or else phone will not be able to enter into download mode.

Attention : Please follow the instructions carefully. I will not take any responsibility on whatever may happen with your phone.
Very important warning : Always make sure that you trust the sources of the ROM you download and know that it is meant for your phone. After flashing a wrong preloader, your phone will be completely dead (can't be powered on, it will not charge and won't be detected anymore by the computer).

Credits : DR_MOOSAVI (from XDA)
Source : http://forum.gsmhosting.com/vbb/f929/guide-all-huawei-android-stock-rom-installation-guide-1845252/ 

Babar Abbasi

Categorie-s

Readers Location

Highlighting country from Readers
Belgium
42.86%
42.86%
Senegal
28.57%
28.57%
Morocco
14.29%
14.29%
France
9.52%
9.52%

Data update in end of each hour. You can update it manual by pressign update button

Articles

Articles report
Subject Activity
Web Development
85%
Networking
40%
Linux
72%
AngularJS
80%
Virtualization
100%
Microsoft Windows
100%

Articles

Benchmarking Guidelines

Membership

How to do a strategic analysis

Visitors

Visitors (last month)

Website builded by Pipo Bengeloune with the famous Drupal CMS.

Log Out ?

Are you sure you want to log out?

Press No if you want to continue work. Press Yes to logout current user.